ASTM D2700-22b

Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel

ASTM International , 12/15/2022

Publisher: ASTM

File Format: PDF

$53.00$107.00

Description

Standard By:ASTM International , 12/15/2022

Published:12/15/2022

Pages:59

File Size:1 file , 1 MB

Language:English

Note:This product is unavailable in Russia, Ukraine, Belarus

1.1This laboratory test method covers the quantitative determination of the knock rating of liquid spark-ignition engine fuel in terms of Motor octane number, including fuels that contain up to 25 % v/v of ethanol. However, this test method may not be applicable to fuel and fuel components that are primarily oxygenates.2 The sample fuel is tested in a standardized single cylinder, four-stroke cycle, variable compression ratio, carbureted, CFR engine run in accordance with a defined set of operating conditions. The octane number scale is defined by the volumetric composition of primary reference fuel blends. The sample fuel knock intensity is compared to that of one or more primary reference fuel blends. The octane number of the primary reference fuel blend that matches the knock intensity of the sample fuel establishes the Motor octane number.

1.2The octane number scale covers the range from 0 to 120 octane number, but this test method has a working range from 40 to 120 octane number. Typical commercial fuels produced for automotive spark-ignition engines rate in the 80 to 90 Motor octane number range. Typical commercial fuels produced for aviation spark-ignition engines rate in the 98 to 102 Motor octane number range. Testing of gasoline blend stocks or other process stream materials can produce ratings at various levels throughout the Motor octane number range.

1.3The values of operating conditions are stated in SI units and are considered standard. The values in parentheses are the historical inch-pounds units. The standardized CFR engine measurements continue to be in inch-pound units only because of the extensive and expensive tooling that has been created for this equipment.

1.4For purposes of determining conformance with all specified limits in this standard, an observed value or a calculated value shall be rounded "to the nearest unit" in the last right-hand digit used in expressing the specified limit, in accordance with the rounding method of Practice E29.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For more specific hazard statements, see Section 8, 14.4.1, 15.5.1, 16.6.1, Annex A1, A2.2.3.1, A2.2.3.3(6) and (9), A2.3.5, X3.3.7, X4.2.3.1, X4.3.4.1, X4.3.9.3, X4.3.12.4, and X4.5.1.8.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D2700-22b

Standard Test Method for Motor Octane Number of Spark-Ignition Engine Fuel

ASTM D2700-22b History

ASTM D2700-24a

ASTM D2700-24

ASTM D2700-23a

ASTM D2700-23b

ASTM D2700-22b

ASTM D2700-22

ASTM D2700-21

ASTM D2700-19e1

ASTM D2700-19

ASTM D2700-18a

ASTM D2700-14

ASTM D2700-13b

ASTM D2700-13

ASTM D2700-13a

ASTM D2700-12

ASTM D2700-11e1

ASTM D2700-11

ASTM D2700-10

ASTM D2700-09

ASTM D2700-09e1

ASTM D2700-08

More ASTM Standards PDF

Conformity assessment kit no. 2

BS 05/30136552 DC

BS NSSF 0010

BS 05/30107773 DC